Commando ALA550 Manual de usuario descargar pdf (Pagina 15)

1/2/02

ALA550 

3. To stop the alarm, press and hold the

or button on the transmitter again for 3 seconds. Also if

any transmitter button other than the

or button is pressed and released, the panic mode will be

turned off immediately.

4. If the button is not pressed, the alarm will automatically stop after 30 seconds.

M. TRIGGER THE SYSTEM

When armed, your vehicle is protected as follows:

1. Light impacts will trigger the warn-away signal. A long chirp from siren/horn.

2. Heavy impacts / Doors open / Hood open / Trunk open / Turn on the ignition key / Activate PIR sensor

/ Activate door/window sensor will trigger the programmed sequence.

The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn, parking

lights, and dome light will turn on to alerting of an intrusion for 30 seconds. Then it will stop and automatic

reset and re-arm. If the one of sensors or detectors still active, the alarm system will sound a maximum of

6 times of 30 seconds cycles.

NOISE ABATEMENT CIRCUIT: Your system has “Noise Abatement Circuit”. It prevents annoying

repetitive trigger sequences due to faulty door pin switches or environmental condition such as thunder,

jackhammers airport noise, etc.

Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time, the same sensor or

switch is triggering the alarm. “Noise Abatement Circuit” will interpret this pattern of triggers as false alarm.

After the fifth trigger, “Noise Abatement Circuit” ignores, or bypasses, that sensor or switch until the other

sensor or switch is triggered.

Doors (Hood/Trunk) are covered by “Noise Abatement Circuit” differently: If the alarm is triggered by an

open door for six full cycles, the door will be bypassed until the trigger ceases.

N. ANTI CAR-JACKING

Warning: If you don't need the anti car jacking function in this alarm system, be sure to set anti car jacking

feature “OFF”. This system is default setting all anti car-jacking “OFF”. (See Alarm Feature

I - 4

Programming.)

ACTIVE ANTI CAR-JACKING

1. TRANSMITTER STAND-BY THE ANTI CAR JACKING:

Press and hold

+ button on the transmitter for 2 seconds while the vehicle’s ignition is ON.

The parking light will turn on for 1.5 seconds to indicate the anti car jacking mode is stand-by

2. DOOR SWITCH ACTIVATE ANTI CAR JACKING:

Under stand-by mode of anti car-jacking mode

1. Turn the ignition switch to “ON” position, the system is armed.

2. Once the system is armed, If you are forced out from the vehicle, the system will active the anti car

jacking trigger when the door is opened and closed.

PASSIVE ANTI CAR JACKING :

It operate as below:

1.Turn the ignition switch to “ON”, the system will arm.

2.If you are forced out from the vehicle, the system will trigger when the door is opened and closed.

TRIGGER THE ANTI CAR JACKING MODE:

3-timer circuits will function as follows:

First timer:

a. 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds.

b. During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off

the car-jacking feature.

c. If not, it will enter second timer anti car jacking.

Second timer:

65 seconds after the system has been triggered. The siren starts alarming and the parking light starts

flashing.

Third timer:

90 seconds after the system has been triggered

a. The siren still alarming and the parking light flashing, and

b. The starter disable will activate to prevent the vehicle from starting.

c. It will remain active until the vehicle's battery power exhausted.

OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR JACKING:

1 2 ... 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

Commando ALA550 Manual de usuario Pagina 15

Comentarios a estos manuales